spacer Cutek CD33 Naked|deck cleaning and stripping|Deck Masters of Canada Cutek Reseller

Best Selection, Best Service, Best Pricing

If you are looking for a specific product and do not see it listed on our website please call or email us your enquiry. It is possible that we can special order it in.
We deliver across Ontario from Windsor to Ottawa and as far north as North Bay/Sudbury. Cross Canada Shipping is available; ask for details. Our drivers help you carry your order to the backyard or dock, otherwise it gets dropped at the curb.

Cutek CD33 Naked

CUTEK® Wood Stripper

CUTEK® Wood Stripper (formerly CUTEK® CD33 Naked) is a powerful and user-friendly paint and surface coating stripper. CUTEK® Wood Stripper is DIY-friendly; no professional experience is necessary.

CUTEK® Wood Stripper is suitable for removing multiple layers of the most commonly used wood coatings such as latex paints, stains, varnishes, linseed oils, acrylics and other film forming coatings. It is also effective at removing coatings from metal, brick and masonry surfaces.

Powerful yet safe, CUTEK® Wood Stripper is the smart alternative to conventional strippers that use dangerous chemicals (such as methylene chloride, NMP, etc.).

PACK SIZES: 3.78 L / 1 US gal

CUTEK Wood Stripper Factsheet PDF

  • Powerful wood stripper
  • Safe and user-friendly
  • Smart alternative
Before Applying

It is important for the user to determine the suitability of CUTEK® Wood Stripper for its intended application. ALWAYS test product on a small test area. The coatings to be stripped can vary significantly, testing will enable you to accurately estimate the working time, and amount of CUTEK® Wood Stripper required to complete your project.

NOTE: CUTEK® Wood Stripper may need to be applied more than once to thick paint or film form coatings with many layers.

Safety and Precautions:

Before you begin to Prepare and Protect your wood, note the hazards and precautions and ensure that you have obtained and know how to use the correct safety equipment as detailed in the Safety Data Sheet.

When using CUTEK® Wood Stripper, all adjacent surfaces and vegetation must be adequately protected. It is also important to be aware of the potential for wind drift into areas with cars or pedestrian traffic when rinsing. Water flush all equipment, vegetation, paths, concrete, asphalt and other adjacent surfaces before and after contact.

Coverage:

Spreading rate is approximately 3 m2/L or 120 ft²/US gal

NOTE: this can vary significantly depending on the type and thickness of the paint or wood coating being removed.

Application

CUTEK® Wood Stripper should be used as supplied. Stir/shake well, then apply CUTEK® Wood Stripper evenly with a brush, roller or paint pad applicator to dry wood, rubbing into the grain. Reaction time is approx. 30-60 minutes. Keep area wet and activated by applying more CUTEK® Wood Stripper or by agitating the application area with a brush or roller for the duration determined by testing.

Test periodically with a paint scraper to determine when the old coating is stripping cleanly off the wood. When this happens, the stripped surface is ready for rinsing. We suggest that you try to strip only 1m² or 10 ft² first.

Removal

Rinse off thoroughly, using a pressure washer set to approximately 50 bar (750 p.s.i.) with a fan jet pattern. REMOVAL WITH A GARDEN HOSE IS NOT SUFFICIENT. CAUTION must be used to avoid damage to the wood fibre and ‘furring up’. Adjust your cleaning process by reducing the pressure or your operating distance from the wood. DO NOT use “turbojets” on wood.

Clean from the lowest point and work upwards methodically using long even strokes in the direction of the grain. If cleaned from the highest point first, the product below can become sticky and difficult to remove.

After stripping the wood, clean it with CUTEK® Wood Reviver to remove residual CUTEK® Wood Stripper and rejuvenate the substrate and enhance the grain. See CUTEK® Wood Reviver for instructions.

Certain types of wood surfaces may leave a raised grain effect after stripping is completed. Sanding or poly pad scrubbing may be required to smooth out this condition.

Clean Up & Disposal

Equipment may be cleaned with CUTEK® Quickclean or soap/detergent and water. All wash water, containers/contents should be disposed in accordance with local regulations


instagram visit us on Facebook Deck Masters of Canada on YouTube

Main Showroom/Head Office: 4745 8th Line, Beeton (New Tecumseth), ON L0G 1A0 416-881-3325 or 1-866-765-2935 sales@deckmasters.ca

Toronto East Showroom:  25 Salome Drive, Unit 3, Toronto, ON M1S 2A7 416-609-8100 sales@deckmasters.ca

Design/Hosting by Inkwell Images & Design