spacer Cutek Proclean|Stains and Cleaners|wood solutions

Best Selection, Best Service, Best Pricing

If you are looking for a specific product and do not see it listed on our website please call or email us your enquiry. It is possible that we can special order it in.
We deliver across Ontario from Windsor to Ottawa and as far north as North Bay/Sudbury. Cross Canada Shipping is available; ask for details. Our drivers help you carry your order to the backyard or dock, otherwise it gets dropped at the curb.

Cutek Proclean Professional Wood and Bamboo Restoration

CUTEK® Wood Reviver

CUTEK® Wood Reviver (Previously CUTEK® Proclean) is a powerful wood cleaning agent that restores stained, weathered and grey wood back to its original appearance.

CUTEK® Wood Reviver is effective in removing stubborn stains caused by tannins, water, iron, resins, mould and fungus. It also removes the common invisible glaze (mill glaze) to prepare newly sawn or machined wood for coating.

CUTEK® Wood Reviver is a one-step brightener and cleaner of many types of stains; it will brighten, clean and restore wood to look like new, ready for coating with CUTEK® Extreme.

PACK SIZES: 3.78L /1 US gal

CUTEK Wood Reviver Factsheet PDF

  • Powerfully restores wood
  • Removes stubborn stains
  • Prepares new wood for coating
Before Applying

It is important for the user to determine the suitability of the CUTEK® Wood Reviver for its intended application. ALWAYS test product on a small test area prior to applying to any large sections. As the species and condition of wood can vary significantly, testing will enable you to accurately estimate if dilution is required, working time, and amount of CUTEK® Wood Reviver required to complete your project.

Safety and Precautions

Before you begin to Prepare and Protect your wood, note the hazards and precautions and ensure that you have obtained and know how to use the correct safety equipment as detailed in the Safety Data Sheet.

When using CUTEK® Wood Reviver, all adjacent surfaces and vegetation must be adequately protected. It is also important to be aware of the potential for wind drift into areas with cars or pedestrian traffic when rinsing. Water flush all equipment, vegetation, paths, concrete, asphalt and other adjacent surfaces before and after contact.

Coverage

Spreading rate is approximately 1 Litre of CUTEK® Wood Reviver per 5-8.5m2 of surface area, or 1 US gal of CUTEK® Wood Reviver per 200-350 ft2 of surface area to be restored.

CUTEK® Wood Reviver is a powerful wood restoring agent and can be used diluted or undiluted. Coverage can vary depending on the smoothness and density of your wood as well as the severity of staining and/or weathering. Always test to determine if your chosen dilution is effective in the restoration of your specific wood

Application

Wet your wood prior to applying CUTEK® Wood Reviver. Apply CUTEK® Wood Reviver liberally to wetted wood with a brush, roller, broom or low-pressure garden sprayer.

Let CUTEK® Wood Reviver do the work by leaving it on the surface for 1 hour to 24 hours depending on the severity of staining or discolouration. It may be necessary to scrub stubborn stains moderately with a stiff fibre brush

Removal

Rinse off thoroughly, using a pressure washer set to approximately 50 bar (750 p.s.i.) with a fan jet pattern. REMOVAL WITH A GARDEN HOSE IS NOT SUFFICIENT. CAUTION must be used to avoid damage to the wood fibre and ‘furring up’. Adjust your cleaning process by reducing the pressure or your operating distance from the wood. DO NOT use “turbojets” on wood.

Rinse from the highest point and work down methodically using long even strokes in the direction of the grain, until there is minimal to no sudsing. The longer that CUTEK® Wood Reviver is left on the wood, the greater the rinse time required.

Note: certain types of wood surfaces may leave a raised grain effect after pressure washing is completed. Sanding or poly pad scrubbing may be required to smooth out this condition.

Clean Up

Equipment may be cleaned with water. Ensure wash water is disposed in accordance with local regulations.


instagram visit us on Facebook Deck Masters of Canada on YouTube

Main Showroom/Head Office: 4745 8th Line, Beeton (New Tecumseth), ON L0G 1A0 416-881-3325 or 1-866-765-2935 sales@deckmasters.ca

Toronto East Showroom:  25 Salome Drive, Unit 3, Toronto, ON M1S 2A7 416-609-8100 sales@deckmasters.ca

Design/Hosting by Inkwell Images & Design